How to safely operate the wire cutting machine?

Work efficiency and quality of work can only be guaranteed in a safe and stable working situation. In order to avoid damage and damage to the machine and personnel of the wire cutting machine, the following items should be noted when operating the wire cutting equipment:

1. Only personnel trained in such machinery and equipment can be approved to use the machine.

2. In order to avoid overheating of the processing fluid and the electrical cabinet, the cooling system must be in continuous operation;

3. In order to avoid direct contact with the energized wires, the machine guard door must be closed;

5. The processor should be proficient in the specific functions of the buttons on the operation panel and the state in use. It can be used flexibly during the operation of the machine, and is familiar with the conversion of the screen, especially several important images (such as preparing the screen and observing the screen). It has the function to avoid various abnormalities caused by unfamiliar operation panel during processing, and the high-intensive use of each button (especially the common button) is easy to be damaged, so when the panel is operated, the surface should be attached with a layer of plastic. Paper protection to extend the life of the operator panel;

6. Like the operation panel, the processor should also be familiar with the specific use method of the remote control. The button on the remote control should be protected by a layer of plastic paper. In addition, the remote control can be operated remotely from the operation panel. The wires are conductive, so the protection of the remote control should also include protection of the wires. During the use process, the wire should not be pulled vigorously to avoid the malfunction of the remote control. The part of the wire column should be placed in a circle. After use, it must be put back in the original place;

7. When the machine tool or the machine head moves, never put the finger of the hand between the machine head and the work object. If the error is caused by the instruction or the direction key is pressed incorrectly, it may cause a safety accident;

8. Protection of processing platform: When processing the workpiece, it should be noted whether the clamping method will hurt the processing platform. When the machine is used, the platform should be blown dry. When it is not used for a long time, the anti-rust oil should be used to protect the machine tool;

9. During the erection of the workpiece, it should be noted whether the upper and lower heads will be hit during the cutting. For the processing of small holes, special processing technology should be adopted to avoid the jamming caused by the inability to remove the waste, which affects the accuracy of the machine tool;

10. The clamping of the workpiece is based on the principle of convenience and stability. When the workpiece is erected, the pressing force is based on the principle that the workpiece is not impulsive by water, so as to avoid the screw slip and cannot be removed;

11. In daily work, you often encounter workpieces that cannot be machined using the general frame mold method. In this case, special clamping fixtures must be used:

(1) Small workpieces - when the platen cannot be erected, it can be processed by using a protractor or mascara;

(2) In the case of large-slope type workpieces - when it is impossible to tilt the machine, it should be processed by a sinusoidal or inclined block-assisted tilting processing method;

(3) When processing multiple pieces - it is possible to consider the use of a protractor or mash for overlap processing

(4) During the use of the jig, it should be ensured that the jig is not damaged. (For example, it is not feasible to injure the jig in the cutting for the convenience of the mold)

12. Special attention should be paid to the equipment during processing: whether the voltage of the voltmeter is within the specified standard range;

13. During processing, the workpiece and copper wire should not be touched directly by hand. When blanking, pay attention to the phenomenon of the head of the material. When the material is difficult to remove, be careful not to damage the equipment and fingers.

14. When cleaning the processed materials, the oxalic acid cleaning solution should be used. When using, the processed material should be washed with a brush instead of using the hands to directly contact the oxalic acid cleaning work, thereby reducing the corrosion of the oxalic acid opponent. Into the eyes, if it is inserted, it should be washed immediately with water;

15. After cutting the machine, the operator should pay attention to washing hands frequently, especially before eating, to avoid the ingestion of the processing fluid that is more contaminated;

16. When performing various repairs and tests on the inside of the power cabinet or on the electrical components of the machine tool, the main switch must be set to the OFF position, and the signboard should be set up (do not turn on the power during maintenance);

17. Safety instructions must be observed during repairs and inspections, and the appropriate sections of the manual must be consulted before any repair work;

18. Only when the control cabinet is powered off can the electronic components be touched;

19. Only hold the handle when holding the component, do not touch the gold-plated wire of the printed circuit board;

21. Attention should be paid to the timely replacement of the consumable parts of the equipment to maintain accuracy.